Below are the engineering certificate programmes we offer and their contents.

1. Certificate in Industrial Automation and Control Engineering

 Content

• Industrial HSE Training
• Engineering Report Writing
• Industrial Pneumatics and Electro-Pneumatics Control Systems
• Programmable Logic Controllers (PLC) – (Siemens S7, Allen-Bradley,)
• Instrumentation and P& ID
• SCADA Essentials (WINCC Flexible /FactoryTalk View)
• Industrial Process Control System (ICS)
• Drive Technology -Basic AC Frequency Drives (Siemens and Danfoss) • Calibration of Process Instruments • Industrial Electric Motors

2. Certificate in Electrical and Electronics Engineering 

 Content  

• Industrial HSE Training
• Engineering Report Writing
• Introduction to Reading of Electrical Drawings and Diagram
• Industrial Electronics equipment (Repairs and maintenance)
• High Voltage Power Systems Training
• Electrical wiring, Earthling, Bonding, and surge Protection of electrical Systems and equipment
• Maintenance of Electrical Systems – Using schematic diagrams Industrial Electric Motor control
• Programmable Logic Controllers (PLC) – (Siemens S7)
• Industrial Pneumatics and Electro-pneumatics control systems 

 3. Certificate in Instrumentation & Controls Engineering 

Content

• Industrial HSE Training
• Engineering Report Writing
• Calibration of Process Instruments
• Instrumentation and P& ID
• SCADA Essentials (WINCC Flexible /FactoryTalk View)
• Industrial Electric Motor control
• Programmable Logic Controllers (PLC) – (Siemens S7)
• Industrial Process Control System (ICS) • Control Valves, Flow, Mass, and Level Measurement
• Temperature and Pressure Measurement 

4. Certificate in Electrical and Instrumentation Engineering

Content

• Industrial HSE Training
• Engineering Report Writing
• Calibration of Process Instruments
• Instrumentation and P& ID
• High Voltage Power Systems Training
• Maintenance of Electrical Systems – Using schematic diagrams
• Industrial Electric Motor control • Programmable Logic Controllers (PLC) – (Siemens S7)
• Industrial Process Control System (ICS)
• Industrial Pneumatics and Electro-pneumatics control systems 

 5. Certificate in Industrial Electromechanical Engineering

Content

• Industrial HSE Training
• Technical Report Writing
• Industrial Pneumatics/Electro-Pneumatics Control Systems
• Practical Pumps and Compressors Technology: Operation, Troubleshooting & Maintenance
• Industrial Electrical Maintenance
• Mechanical Drives and Lubrication
• Programmable Logic Controllers (PLC) – (Siemens S7)
• Industrial Electric Motors: Operation, Troubleshooting and Maintenance
• Heating, Ventilation and Air Conditioning/Refrigeration (HVAC/R): (Operation, Troubleshooting and Maintenance)
• Industrial Hydraulics and Electro-Hydraulics Control Systems 

6. Certificate in Solar Power Systems Engineering

Content

• Industrial HSE Training
• Engineering Report Writing
• Introduction to Reading of Electrical Drawings and Diagram
• Electrical Wiring System
• Electrical Faults causes, Analysis, Detection and Remedies
• Renewable (Solar) Energy Fundamentals
• Solar Photovoltaic Technology
• Installation and Maintenance of solar Electric systems
• Variable Frequency Drive
• Solar Electric System Design 

 7. Certificate in Utilities and Power Systems Engineering

Content

• Industrial HSE Training
• Engineering Report Writing
• Industrial Electrical Maintenance
• Pumps and Compressors: (Principles, operation, and Maintenance)
• Heating Ventilation and Air-conditioning and Refrigeration Systems (HVAC/R)
• Diesel Generator Maintenance Optimization: Principles, Operation and Maintenance
• Instrumentation and P & ID • Industrial Hydraulics and Electro-Hydraulics Control System
• Programmable Logic Controllers (PLC) – (Siemens S7) • CO2 and Water Treatment Plant

 8. Certificate in Heating, Ventilation and Air-Conditioning/ Refrigeration (HVAC/R) Systems

Content

• Workshop Practice and Welding Safety
• Engineering Report Writing
• Refrigeration and Air-Conditioning Science and Calculation
• Gas Welding (Brazing), Duct Design, Air Flow, and Its Distribution
• Refrigeration and Air-Conditioning System
• Heating Ventilation and Refrigeration Systems (HVAC)
• Condenser, Evaporator, Compressor, Metering device and Other Refrigeration Devices
• Electrical Controls and Instrumentation in HVAC-R systems
• Cold Room, Chiller, Ammonia System and Cooling Tower
• Installation Testing Commissioning of HVAC/R systems 

This program runs for a duration of 1 Month for Weekday (MON-FRI) and 2 Months Weekends (SAT & SUN) 

Entry Requirements: B. Eng., B. Sc., HND, B.Tech., OND, City & Guilds and Undergraduates of tertiary Institutions

NB: A registration of #5,000 is being paid, thereafter training fee